Do you have a sewage treatment solution for a site that is prone to seasonal flooding?

The question above was an interesting one we received from a French customer this week. A lot of sewage treatment plants are installed in the lowest area of a site to try and achieve gravity flow into it. However, with more intense rainfall becoming the norm, low lying areas can often be prone to surface flooding. Sometimes large areas of sites can be subject to flash flooding and ponding.
The good news is Butler Manufacturing Services can offer a number of different solutions:
1. If the installation location is subject to flash flooding you can install our market leading Blivet Sewage Treatment Plant completely above ground and then pump the sewage up to it. The top of the Blivet is 2.3 m above ground so as long as the inlet and outlet pipes are water tight, this solution along with anchoring to a concrete slab and water tight electrical conduits, will ensure continuous sewage treatment even during flooding. Of course the only down side is that sewage needs to be pumped to the treatment plant. You can see a good example below of a plant installed with anchoring to resist seasonal/flash flooding.
2. In the above case floodwaters can rise to 2.5 m, so we recommended to the customer that the Blivet is installed on a 0.5 m raised slab, meaning the Blivet will be above the max flood level with an extra 200 mm safety margin.
3. For a lower lying area with some ponding, BMS can work with you to install a surface water drainage solution around the plant, to make sure that no flood water enters the plant, drawn from our complete one stop shop for surface water management.
4. Another solution is to install our Blivet Sewage Treatment System in a concrete basin with a prefabricated shed above it and some surface water management.
We cannot say we have seen every scenario but having manufactured sewage treatment plants since 1986, which have been exported to 50+ countries, so we have seen a lot and have had to come with up some very innovative solutions.


If you have sewage treatment project with an installation prone to ponding/flooding or any other sewage treatment project, please contact BMS on +353433326100 or email: info@butlerms.com or log on to www.butlerms.com

Example of BMS Blivet Sewage Treatment Plant installed above ground with anchors to mitigate against intermittent site flooding.

BMS is a quality manufacturer of package products for wastewater and stormwater treatment. BMS started in 1986 and has exported products to over 50 countries around the world.  It is a third generation family business with huge expertise in wastewater and stormwater.


BMS also manufacture a full range of products for surface water and wastewater treatment including our pioneering next generation RBC system the Aerotor, which forms part of our world leading Blivet package sewage treatment plant, a ‘one stop shop’ for all surface water products from design to installation including attenuation, interceptors, holding tanks (incl. chemical resistant), hydrobrakes, rainwater harvesting tanks & vortex silt/oil/debris separators, fully fitted pumping stations, our plug & play vehicle wash water recycling system; the Recyclone and much more.  Please see our enclosed Company & Product Profile for a full summary or View our full product/services catalogue at this link

BMS also can provide a Free Design Service for Sewage Treatment, Pump Stations or Surface Water and a full O&M, Repair, Advice and Testing service for existing installations.  We also can do free CPD Presentations on Sewage Treatment/Surface Water Management at any location. 

A bit about the company

BMS is a quality manufacturer of package products for wastewater and stormwater treatment. BMS started in 1986 and has exported products to over 50 countries around the world.  It is a third-generation family business with huge expertise in wastewater and stormwater.


BMS also manufacture a full range of products for surface water and wastewater treatment including our pioneering next generation RBC system the Aerotor, which forms part of our world-leading Blivet package sewage treatment plant, a ‘one stop shop’ for all surface water products from design to installation including;

Please see our enclosed Company & Product Profile for a full summary or View our full product/services catalogue at this link

BMS also provides:

  • Free Design Service for Sewage Treatment, Pump Stations, and Surface Water Treatment

  • Full Operation and Maintenance, Repair, Advice, and Testing services for existing installations.

We also can do free CPD Presentations on Sewage Treatment/Surface Water Management at any location. 

We would be delighted to discuss any requirements you might have, and we are available to meet you at your convenience.  Contact us today.

Tommy Bulter

M.Pharm (Hons) MBS (Hons) Cert. H&S (Allison)
• 15 year’s + experience in Management in Waste/Surface Water, R&D & H&S.
• Project Management specialist, Marketing specialist, Pharmacist, Wastewater and pump specialist.

https://butlerms.com
Previous
Previous

How you calculate the correct size of Grease Trap?